物理吸附式干燥處理機

◆護膚品特性 Product features

※含有保持穩定相符的排氣氣壓和露點

1.樹脂吸附塔之高與厚度經實驗操作結論精密五金來計算，塔床的阻力小，確定了再壓縮有毒氣體變干劑5秒的碰觸時候，需求原料氣的露點符合要求。

2.30％的常溫、晾干劑的余量，應用在補償金常溫、晾干劑的自然生態氧化，提高認識常溫、晾干。

3.超大型分散器，保證 氣體流動飽滿按照干燥處理劑層，減少溝流表現。

※回收氣量損耗率值為14％

1.優秀的機筒制定，導出100％的離心分離脂肪含量，貯藏的脂肪含量使用提高了凈化階段性的凈化氣溫，提高了的設備的解吸本事，這讓凈化更恢復原狀。

2.干澀和回收利用通過方向過流實施方案，濕熱空氣流淌干的氣體吸附劑時長果更佳。回收利用氣出口貿易含濕量管控在亞臨界狀態下狀態下，使消音器器及res排氣管道無結霜現象之慮。

3.可通過干燥處理機的開機運行電機負載要調結可重復利用能力氣需水量，確定可重復利用能力氣旋連續式增強，可重復利用能力重壓低至臨介。

※粗糙劑食用時間長

1.比較適合的機筒長度，使氣體實現干躁劑層的水流量和事件增加好的模式，全面發揮出來干躁劑的能。

2.有效的系統軟件顯卡配置，在暖濕暖濕氣流進入機筒前，經除油加工要及時清理掉暖濕暖濕氣流中內油份物與重生態破壞物，防范低溫干燥劑層受生態破壞。

※環保設備適用了有意思高品行電動及手動閥和是真的嗎的全自行化可編寫程序序調整器，組隊軟件界面親善，自行陸續屏幕上顯示雙塔工程環境，巡環周期時間直播 可編，出貨確定10min。伐門生命周期短短50萬次運作。

※筒身開口處作冷熱鍍鋅除銹清理，10年不脫漆。

※小動作為準、能力安全、進行操作簡便方法，重新安裝不能自己的基礎。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆關鍵的技術規格 Main technical parameters